引用本文:
【打印本页】   【下载PDF全文】   View/Add Comment  Download reader   Close
←前一篇|后一篇→ 过刊浏览    高级检索
本文已被:浏览 1728次   下载 1636 本文二维码信息
码上扫一扫!
分享到: 微信 更多
钝顶螺旋藻部分原生质体及单细胞的制备与培养
秦松, 王希华, 童顺, 曾呈奎
中国科学院海洋研究所 青岛 266071
摘要:
于1992年1月 - 1994年4月,进行超声波处理方法制备钝顶螺旋藻部分原生质体以作为基因工程受体,以及制备单细胞用于固体平板克隆化培养的研究。研究结果表明:超声波以20kHz频率、15W功率作用30s,可使藻丝体断裂成15.0±1.6个细胞长度;延长作用时间,至2-6个细胞长度时,细胞壁结构遭到破坏,形成部分原生质体;继续作用,可形成少量原生质体和大量单细胞。断裂藻丝体、部分原生质体、单细胞以及原生质体均可涂布于固体培养基上再生或生长。以一定密度涂布单细胞与原生质体,能够形成彼此分开的单个克隆,可用于筛选及遗传分析。本文提供了一种节省溶菌酶的制备螺旋藻透性体的方法,超声波作用利于外源基因的导入,而涂布培养利于进一步的筛选和形成克隆。
关键词:  钝顶螺旋藻  单细胞  透性体  克隆  原生质体
DOI:
分类号:
基金项目:
ISOLATION AND CULTURE OF PERMEAPLASTS AND SINGLE CELLS FROM SPIRULINA PLATENSIS
Qin Song, Wang Xihua, Tong Shun, Zeng Cherigkui (C. K. Tseng)
Institute of Oceanology, Academia Sinica, Qingdao 266071
Abstract:
Jan., 1992 to April, 1994 studies carried out on isolation of spheroplasts for gene introduction and single cell for plating showed: 1. filaments of Spirulina platensir can be broken by ultrasonics into disired average length fragments; 2. when the length was 2—6 cells, cell walls were partially removed and permeaplasts were formed; 3. with prolonged treatment few protoplasts and many single cells appeared; 4. fragments single cells and protoplasts can regenerate or grow by plating on solid medium; 5. plating single cells and protoplasts after dilution may be a useful method for cloning and selection. The results, suggesting a lysozyme-saving method for permeaplast preparation, indicate that ultrasonics is helpful for gene introduction, and that plating is good for genetic analysis and cloning of filamentous algae.
Key words:  Spirulina plazensis, Single cell, Permeaplast, Clone, Protoplast
Copyright ©  Editorial Office for Oceanologia et Limnologia Sinica    Copyright©2008 All Rights Reserved
Supervised by: China Association for Science and Technology   Sponsored by: Chinese Society for Oceanology and Limnology, Institute of Oceanology and Limnology, CAS.
Address: 7 Nanhai Road, Qingdao, China.    Postcode: 266071    Tel: 0532-82898753  E-mail: liuxiujuan@qdio.ac.cn  
Technical support: Beijing E-Tiller Co.,Ltd.